--- comments: - comment: Now loaded 1.0.8.16 to my 486. Short CLID issue still not resolved. created: 2006-02-14 10:41:46 name: stevehuggons@ntlworld.com - comment: "Software Version: \t Program-- 1.0.7.19 Bootloader-- 1.0.8.9 HTML-- 1.0.7.18 VOC-- 1.0.0.10" created: 2006-02-14 16:33:03 name: rival@freemail.hu - comment: Yes finally - It\'s working again...:-) And best of all my wife is happy again;-) created: 2006-02-14 18:56:00 name: Brian Svendsen - comment: Program-- 1.0.8.16 Bootloader-- 1.0.8.9 HTML-- 1.0.8.16 VOC-- 1.0.0.10 created: 2006-02-14 21:13:22 name: alexander - comment: Working fine for 2 days now. created: 2006-02-16 20:26:17 name: alexander - comment: mine is dead after update... created: 2006-02-16 22:19:44 name: blackbile@index.hu - comment: NEED LAST FIRMWARE created: 2006-02-18 22:21:16 name: asaflidor@hotmail.com - comment: Why is firmware running as \"latest\" still 1.0.6.7, is this really last stable version? created: 2006-02-20 16:08:56 name: Michael K. - comment: Just upgraded to 1.0.8.16 from 1.0.6.7. Initial tests look OK. However firmware version shows 1.0.6.8. created: 2006-02-20 21:13:21 name: Tony.Friar@newkinetics.co - comment: Michael, 1.0.6.7 is the latest official release from Grandstream. Newer versions are ALL beta. created: 2006-02-21 17:41:06 name: alexander - comment: The 486 rev 2 froze twice today and I had to remove the power plug to reset. This also happened occasionnally on older firmware versions too created: 2006-02-23 21:23:38 name: alexander - comment: Why all these new bootloaders? Is it to \"avoid\" going back to older versions? Always, same result - the phones are \"disabled\". Now, my BT100 not work more. It does not allow old versions for phone, since it now use bt_110.bin.. created: 2006-02-24 18:26:31 name: ccc41290@vip.cybercity.dk - comment: It exists several BT100 versions, you may not have same troubles. Size of firmware memory may differ, even same number of phone. Older than my phone still works, and does not change to newer versions. Newer, may function. But some go off. created: 2006-02-24 18:28:46 name: ccc41290@vip.cybercity.dk - comment: Tony - you have the old BT100 model, that works. It upgrades only to 1.0.6.8. Maybee your phone not supply more ringtones (only system tone). created: 2006-02-24 18:32:15 name: ccc41290@vip.cybercity.dk - comment: Now it works. I am not sure what did it, but after booting from http, and not tftp, it worked. More things was done, and not sure if that was what made it work. Seem to be stable enough. created: 2006-02-24 19:07:52 name: ccc41290@vip.cybercity.dk - comment: Just upgraded from 1.0.6.7, showing now Program-- 1.0.8.16 Bootloader-- 1.0.8.9 HTML-- 1.0.8.16 VOC-- 1.0.1.0 . Works fine. created: 2006-02-24 19:46:54 name: muewi - comment: I\'ve tried to upgrade but still shows as 1.0.6.7 - anybody help? created: 2006-02-27 20:57:10 name: HWD - comment: On Grandstream site 1.0.8.16 now shows as current! created: 2006-03-01 10:28:06 name: telenieko - comment: After upgrad, unit is fuctionnal BUT ADMIN PASSWORD IS DEAD. Unit is locked. Any ways to unlock it ??? created: 2006-03-03 17:25:17 name: 6123@quiconnect.com - comment: Needed to perform reset to factory settings to re-access my phone. Now works fine. created: 2006-03-03 18:08:44 name: 6123@quiconnect.com - comment: HT486 rev 2 - Just upgraded from 1.0.6.7. No problems so far! I noticed there\'s no link to the zip file on the GS site, just the TFTP location, so I downloaded from /BETATEST and used my own tftpd created: 2006-03-04 00:44:01 name: ChrisW - comment: Can anybody confirm if they can ping the HT486 REV 2 on the WAN port if the \'Reply to ICMP on WAN port\' option is enabled? It is not working for me and I\'m sure it did work in the past before upgrading to 1.0.8.16. created: 2006-03-05 19:08:18 name: alexander - comment: Yes I can ping the WAN port from another machine not connected to the ATA, but I\'m using Bridged mode created: 2006-03-05 23:58:55 name: ChrisW - comment: Thanks ccc41290 - I have just seen your comment - I came back to this site to say I have just upgraded 2 BT100\'s. One showed a product model of BT100 and the other showed BT100 REV 2.0. The REV 2.0 upgraded to 1.0.8.16. The other shows 1.0.6.8 created: 2006-03-07 15:28:05 name: Tony.Friar@newkinetics.co - comment: Sorry, I\'ve upgraded a newer BT100 which took 1.0.8.16 and before the upgrade it only showed BT100 and not BT100 REV 2.0. The REV 2.0 only appears to appear after the upgrade. I\'m not sure how you tell the hardware version. created: 2006-03-08 10:38:59 name: Tony.Friar@newkinetics.co - comment: CID presentation has been removed for my TeleDanmark Logger II Plus in this firmware. None of the Caller ID schemes work anymore. Somewhat unstable webinterface. And I can\'t go back to 1.0.6.7 to make my HT486r2 useful again - hmm... created: 2006-03-08 15:44:18 name: Michael - comment: The phone works fine, but I can no longer see the number of the person who is calling me. (I use a B&O telephone). I have set the Caller ID scheme to \"DTMF-Denmark\" like I did in the old version, but this seemes to have no effect. created: 2006-03-09 20:38:40 name: Erik - comment: "Got mail from Grandstream today: \\\"We are aware of the issue. It will be fixed in our next firmware release.\\\"" created: 2006-03-10 14:15:50 name: Erik - comment: Grandstream confirmed that my ping issue is a bug. You can toggle the setting in the config. After pressing Update it will work. You will have to toggle it again after each reboot to make it work. created: 2006-03-10 19:16:08 name: alexander - comment: Why the Ringer volume always going back to its loudest position when doing a power reboot ? It would be nice to have a setting for this in the admin tool. created: 2006-03-11 10:52:08 name: TonyB - comment: Why the Ringer volume always going back to its loudest position when doing a power reboot ? It would be nice to have a setting for this in the admin tool. created: 2006-03-11 11:05:33 name: TonyB - comment: My sipgate account doesnt work properly with 1.0.8.16 firmware - phone can not register to the network, sometimes is registering so I am confused, do not know why is so unstable? created: 2006-03-13 15:46:43 name: Dariusz - comment: We have plenty of these phones and they lose registration much more than what they used to with 1.0.6.7 or 1.0.7.11 created: 2006-03-20 09:38:28 name: TimoS - comment: I have to powercycle my HT486 rev 2 each 7+ days or so because it looses connection or freezes. I\'d be interested to know what your experiences are. I have put a timer on de powerplug to switch off at 2:45 am for 15 minutes. created: 2006-04-06 21:20:53 name: alexander - comment: My Binatone DECT MD 1000 handset does not pick up the correct time feed from the 486 any longer. This seems to be after updating to 1.0.8.16. I have advised grandstream of this and they are investigating. created: 2006-04-06 21:59:13 name: stevehuggons@ntlworld.com - comment: Steve, same problem here. Seems to be a problem with the time.nist.gov server. Try switching to a different time server (list at http://ntp.isc.org/bin/view/Servers/StratumOneTimeServers). This solved the problem for me. created: 2006-04-07 20:43:29 name: alexander - comment: Alexander, I am in the UK & to get the time anywhere close to what it should be I have now stopped using London as a time zone and I am using GMT+4. I have tried some other NTP servers and I can get the time within 6 minutes of the real time.. created: 2006-04-07 22:33:02 name: stevehuggons@ntlworld.com - comment: using GMT + 4. Where are you located and which NTP server do you use? I think that this may be a bug that has been introduced through the new firmware. created: 2006-04-07 22:34:07 name: stevehuggons@ntlworld.com - comment: "Steve, I\\'m in the Netherlands (GMT+1). I use NTP server: ntp0.nl.uu.net and it is accurate within 1 minute." created: 2006-04-08 11:30:59 name: alexander - comment: Alexander, I have tried ntp0.nl.uu.net and for me ihe time is 18 minutes slow. I really dont know what could be causing this issue. created: 2006-04-08 12:19:39 name: stevehuggons@ntlworld.com - comment: Steve, I haven\'t tried this yet but could this be related to Daylight Savings Time. That\'s about the only thing that has changed in my config. created: 2006-04-10 20:34:15 name: alexander - comment: Changed back to ntp.sipgate.net and the minutes are now correct. I have had to set the time zone to GMT + 4. I should be able to use London, but the time would be 4 hours out! created: 2006-04-10 21:20:32 name: stevehuggons@ntlworld.com - comment: I have found out what is causing and how to resolve the problem with the time on my telephone. If the TFTP address is left blank in the Firmware Server Path created: 2006-04-26 19:53:37 name: stevehuggons@ntlworld.com - comment: (168.75.215.189), the time and the time zone always show incorrect time information. However, now I have included the IP address in created: 2006-04-26 19:53:47 name: stevehuggons@ntlworld.com - comment: the Firmware Server Path field, I can set the correct time zone (London) and the time is correct on the telephone handset created: 2006-04-26 19:54:04 name: stevehuggons@ntlworld.com - comment: Correct, if the Firmware Server Path is filled with a TFTP address, the time is correct, otherwise, not. created: 2006-04-27 21:26:14 name: muewi - comment: It is a shame that I had to investigate this and identify the issue as grandstream did not have a clue! created: 2006-04-27 23:50:56 name: stevehuggons@ntlworld.com - comment: There seems to be no way setting TFTP config path by using voice menu (***) :( created: 2006-05-16 12:47:32 name: TimoS - comment: I just updated from 1.0.6.7 to 1.0.8.16 and glad to see that many bugs were fixed :) created: 2006-05-16 22:26:13 name: jul-fr - comment: but now, i cant ping my HT486 although the \"ICMP on wan\" is set to yes :-( created: 2006-05-16 22:30:17 name: jul-fr - comment: Applied 2 weeks ago and no problems so far created: 2006-05-22 13:05:49 name: Terry Reilly - comment: For 1 wk my HT does not accept incoming calls from my VOIP provider in the afternoon and I must reboot. I already powercycle every night. On established calls the caller cannot hear me but when I call back the call is ok. Status says HT is registered created: 2006-06-02 21:53:59 name: alexander - comment: For 1 wk my HT does not accept incoming calls from my VOIP provider in the afternoon and I must reboot. I already powercycle every night. On established calls the caller cannot hear me but when I call back the call is ok. Status says HT is registered created: 2006-06-02 21:54:59 name: alexander - comment: I placed the HT in my router\'s DMZ. Not sure why this stopped working as I did not change my router\'s config. created: 2006-06-05 10:50:52 name: alexander - comment: "Still this problem: phone shows registration mark on screen, but doesn\\'t recive any calls. Dialing out works just great. What might be the problem?" created: 2006-06-05 10:51:08 name: TimoS - comment: My 486 (rev. 2) froze twice yesterday (on outgoing calls) => need to plug out/in the power supply to reset.. Already got this few days ago... created: 2006-06-11 18:43:32 name: Arnaud - comment: My 486 (rev. 2) froze twice yesterday (on outgoing calls) => need to plug out/in the power supply to reset.. Already got this few days ago... created: 2006-06-11 18:43:38 name: Arnaud - comment: My 486 (rev. 2) froze twice yesterday (on outgoing calls) => need to plug out/in the power supply to reset.. Already got this few days ago... created: 2006-06-11 18:44:36 name: Arnaud - comment: I never experienced lock-ups during calls. Unit freezes after some days. I now have the unit on a timer cuasing it to reboot at 3 am. created: 2006-06-15 23:58:03 name: alexander - comment: I put the TFTP server of grandstream. Something happend and know my HT 486 doesn\'t work anymore. Even the voice menu and web configuration are dead. How can I fix this??? No tone either... created: 2006-08-07 01:15:26 name: pedroggf@gmail.com note: See release notes. phone: BT100_HT286_HT486 uploaded: 2006-02-14 09:12:57 uploader: sorend@rediffmail.com version: 1.0.8.16